LiPo Battery 201034
The HHS 201034 is an ultra-thin lithium polymer cell in the HHS Energy polymer range, with a stated capacity of 40 mAh at 3.7V. Its stated size is 2.0 mm thick, 10 mm wide and 36 mm long. The 2.0 mm thickness is the defining feature: it suits devices where thickness is the limiting dimension, such as slim wearables, thin cards, compact sensors and flat portable devices that cannot take a thicker cell.
The cell is supplied with a protection circuit module and can be supplied with leads or a connector to match the device. Protection boards stated for the polymer range are DW01 plus 8205 and G3J plus 8205 combinations. The stated cycle life is 600 cycles or more, and the lead time is 7 days. The listing describes this cell as ultra-thin, which is consistent with the stated 2.0 mm thickness. Custom polymer work covers custom voltages from 3.7V upward, a wide capacity range, custom sizes and shapes, and battery management systems from 10A to 100A and above.
Specifications
| Model | HHS 201034 |
|---|---|
| Nominal voltage | 3.7V |
| Capacity | 40 mAh |
| Size | T2.0 x W10 x H36 mm |
| Description | Ultra-thin, consistent with the stated 2.0 mm thickness |
| Protection | Protection circuit module; DW01+8205 / G3J+8205 boards (as stated for the range) |
| Connection | Leads or connector |
| Cycle life | 600 cycles or more |
| Lead time | 7 days |
Features
Lithium polymer cells in this range are 3.7V pouch cells supplied with a protection circuit module, with leads or connectors to match the device. Protection boards stated for the range are DW01 plus 8205 and G3J plus 8205 combinations. The stated cycle life is 600 cycles or more. Lead time for listed polymer cells is 7 days. Custom polymer work covers custom voltages from 3.7V upward, a wide capacity range, custom sizes and shapes, battery management systems from 10A to 100A and above, and options including charge display, USB charging, communication and balancing.
Minimum order quantity for polymer cells is not stated on the source listings and is confirmed when you inquire. Certificates are available upon request. Where a listing title mentions a size or capacity that the specification body does not state, this site uses the specification body's figures only.
Ordering
Lead time is 7 days. Minimum order quantity is not stated on the source listing and is confirmed when you inquire.
Notes on This Specification
The specification above transcribes the stated figures for the 201034 cell only. The ultra-thin description is used here because it matches the stated 2.0 mm thickness; it is not used as a separate specification claim.
Request a Quote
For specifications, samples, pricing and lead time, please contact us with your voltage, capacity and application. Minimum order quantity and lead time differ by product and are stated on each product page. Certificates are available upon request.
Phone: +86-75528237685 | Email: director@sz-battery.com | Contact form
Related Pages
Design Notes for Device Makers
Designing a device around the 201034 cell starts with its defining trait: 2.0 mm thickness. A device with a slim profile, such as a thin wearable, a smart card or a flat sensor, can fit this cell where a 4.0 mm cell cannot. The footprint is 10 mm wide and 36 mm long, so the compartment must clear that area plus lead or connector routing. The cell's 40 mAh capacity suits devices with low to moderate energy use: a device drawing 1 mA on average runs for well over a day, and a device with intermittent use runs for much longer.
The thin pouch needs protection from bending and pressure in the device housing: a rigid compartment or a backing plate prevents the cell from flexing during use. Charging circuitry must match lithium polymer charging at 3.7V nominal, with the protection board as a safety backup. Confirm the lead or connector type, the quantity and the 7 day lead time with the quote. If the device needs a thinner or thicker cell than 2.0 mm, custom polymer work can quote other thicknesses.