LiPo Battery 401030
The HHS 401030 is a small lithium polymer cell in the HHS Energy polymer range, with a stated capacity of 90 mAh at 3.7V. Its stated size is 4.0 mm thick, 10 mm wide and 32 mm long, including the protection circuit module. It suits compact devices where a small pouch cell is needed: wearables, small consumer electronics, compact instruments and devices with tight internal space.
The cell is supplied with a protection circuit module and can be supplied with leads or a connector to match the device. Protection boards stated for the polymer range are DW01 plus 8205 and G3J plus 8205 combinations. The stated cycle life is 600 cycles or more, and the lead time is 7 days. Like other polymer cells in the range, the 401030 can be the basis for a custom size or capacity: custom polymer work covers custom voltages from 3.7V upward, a wide capacity range, custom sizes and shapes, and battery management systems from 10A to 100A and above.
Specifications
| Model | HHS 401030 |
|---|---|
| Nominal voltage | 3.7V |
| Capacity | 90 mAh |
| Size | T4.0 x W10 x H32 mm, with PCM |
| Protection | Protection circuit module; DW01+8205 / G3J+8205 boards (as stated for the range) |
| Connection | Leads or connector |
| Cycle life | 600 cycles or more |
| Lead time | 7 days |
Features
Lithium polymer cells in this range are 3.7V pouch cells supplied with a protection circuit module, with leads or connectors to match the device. Protection boards stated for the range are DW01 plus 8205 and G3J plus 8205 combinations. The stated cycle life is 600 cycles or more. Lead time for listed polymer cells is 7 days. Custom polymer work covers custom voltages from 3.7V upward, a wide capacity range, custom sizes and shapes, battery management systems from 10A to 100A and above, and options including charge display, USB charging, communication and balancing.
Minimum order quantity for polymer cells is not stated on the source listings and is confirmed when you inquire. Certificates are available upon request. Where a listing title mentions a size or capacity that the specification body does not state, this site uses the specification body's figures only.
Ordering
Lead time is 7 days. Minimum order quantity is not stated on the source listing and is confirmed when you inquire.
Notes on This Specification
The specification above transcribes the stated figures for the 401030 cell only. No capacity, dimension or cycle figure is stated here for any other polymer size; other size codes that appear in the company's lists are not presented as verified models.
Request a Quote
For specifications, samples, pricing and lead time, please contact us with your voltage, capacity and application. Minimum order quantity and lead time differ by product and are stated on each product page. Certificates are available upon request.
Phone: +86-75528237685 | Email: director@sz-battery.com | Contact form
Related Pages
Design Notes for Device Makers
Designing a device around the 401030 cell starts with the footprint: 10 mm wide and 32 mm long, with a thickness of 4.0 mm including the protection circuit module. The device's battery compartment must clear those dimensions plus the lead or connector routing, and the compartment should protect the pouch from sharp edges and pressure points. The cell's 90 mAh capacity suits devices with low average current draw: a device drawing 1 mA on average runs for many days on a charge, while a device drawing 10 mA continuously runs for hours. Peak current should be checked against the protection board's rating before the design is finalized.
Charging circuitry for the device must match lithium polymer charging at 3.7V nominal, with the protection board as the last line of defense rather than the primary control. The device's charging circuit should provide the correct voltage profile and current limit, and the protection board should be treated as a safety backup. For production, confirm the lead or connector type, the quantity and the lead time of 7 days with the quote, and state whether the cell will be supplied loose or pre-wired into the device's assembly.